Sending DHCP requests... time out!

I have connected an ethernet cable and now I have this error:

Leopard 365 :>boot

Loading from NAND 256MiB 3,3V 8-bit, offset 0x400000

  Image Name:   "RR Linux Kernel"

  Image Type:   ARM Linux Kernel Image (uncompressed)

  Data Size:    2921280 Bytes =  2.8 MB

  Load Address: 80008000

  Entry Point:  80008000

Automatic boot of image at addr 0x82000000 ...

## Booting kernel from Legacy Image at 82000000 ...

  Image Name:   "RR Linux Kernel"

  Image Type:   ARM Linux Kernel Image (uncompressed)

  Data Size:    2921280 Bytes =  2.8 MB

  Load Address: 80008000

  Entry Point:  80008000

  Verifying Checksum ... OK

  Loading Kernel Image ... OK

OK

Starting kernel ...

[    0.000000] Linux version 2.6.18-ridgerun (stephane@TAMARA) (gcc version 4.2.4) #1 Thu Jul 15 15:47:25 CEST 2010

[    0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

[    0.000000] Machine: DaVinci DM365 EVM

[    0.000000] Memory policy: ECC disabled, Data cache writeback

[    0.000000] DaVinci DM0365 variant 0x8

[    0.000000] PLL1: oscrate 24000000

[    0.000000]

[    0.000000] PLL0: fixedrate: 24000000, commonrate: 121500000, vpssrate: 243000000

[    0.000000] PLL0: vencrate_sd: 27000000, ddrrate: 243000000 mmcsdrate: 121500000

[    0.000000] PLL1: armrate: 297000000, voicerate: 20482758, vencrate_hd: 74250000

[    0.000000] CPU0: D VIVT write-back cache

[    0.000000] CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets

[    0.000000] CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets

[    0.000000] Built 1 zonelists.  Total pages: 21504

[    0.000000] Kernel command line: console=ttyS0,115200n8 davinci_enc_mngr.ch0_output=COMPOSITE davinci_enc_mngr.ch0_mode=720x480 dm365_imp.oper_mode=0 davinci_capture.device_)

[    0.000000] WARNING: experimental RCU implementation.

[    0.000000] PID hash table entries: 512 (order: 9, 2048 bytes)

[    0.000000] Clock event device timer0_0 configured with caps set: 07

[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

[    0.010000] Memory: 84MB = 84MB total

[    0.010000] Memory: 82096KB available (2237K code, 529K data, 180K init)

[    0.220000] Mount-cache hash table entries: 512

[    0.220000] CPU: Testing write buffer coherency: ok

[    0.220000] NET: Registered protocol family 16

[    0.220000] MUX: initialized SPI0_SCLK

[    0.220000] MUX: initialized SPI0_SDO)

[    0.220000] MUX: initialized SPI0_SDI

[    0.220000] MUX: initialized SPI0_SDENA0

[    0.240000] DaVinci: 104 gpio irqs

[    0.240000] MUX: initialized GPIO20

[    2.240000] MUX: initialized I2C_SCL

[    2.250000] DM365 IPIPE initialized in Continuous mode

[    2.250000] Generic PHY: Registered new driver

[    2.260000] ch0 default output "COMPOSITE", mode "720P-60"

[    2.260000] Invalid id...

[    2.260000] Setmode failed, reset to encoder default...

[    2.260000] VPBE Encoder Initialized

[    2.260000] Leopard DVI encoder initialized

[    2.260000] SCSI subsystem initialized

[    2.260000] usbcore: registered new driver usbfs

[    2.260000] usbcore: registered new driver hub

[    2.270000] NET: Registered protocol family 2

[    2.330000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

[    2.330000] TCP established hash table entries: 4096 (order: 2, 16384 bytes)

[    2.330000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

[    2.330000] TCP: Hash tables configured (established 4096 bind 2048)

[    2.330000] TCP reno registered

[    2.360000] JFFS2 version 2.2. (NAND) (SUMMARY)  (C) 2001-2006 Red Hat, Inc.

[    2.360000] Initializing Cryptographic API

[    2.360000] io scheduler noop registered (default)

[    2.360000] davincifb davincifb.0: dm_osd0_fb: 720x480x16@0,0 with framebuffer size 675KB

[    2.370000] davincifb davincifb.0: dm_vid0_fb: 0x0x16@0,0 with framebuffer size 1020KB

[    2.380000] davincifb davincifb.0: dm_osd1_fb: 720x480x4@0,0 with framebuffer size 675KB

[    2.380000] davincifb davincifb.0: dm_vid1_fb: 0x0x16@0,0 with framebuffer size 1020KB

[    2.390000] DAVINCI-WDT: DaVinci Watchdog Timer: heartbeat 60 sec

[    2.390000] davinci_ldc initialized

[    2.390000] facedetect major#: 252, minor# 0

[    2.390000] facedetect driver registered

[    2.390000] imp serializer initialized

[    2.390000] davinci_previewer initialized

[    2.400000] davinci_resizer initialized

[    2.400000] Serial: 8250/16550 driver $Revision: 1.90 $ 3 ports, IRQ sharing disabled

[    2.400000] serial8250.0: ttyS0 at MMIO map 0x1c20000 mem 0xfbc20000 (irq = 40) is a 16550A

[    2.410000] serial8250.0: ttyS1 at MMIO map 0x1d06000 mem 0xfbd06000 (irq = 41) is a 16550A

[    2.420000] RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize

[    2.440000] loop: loaded (max 8 devices)

[    2.450000] Davinci EMAC MII Bus: probed

[    2.450000] MAC address is 02:00:10:00:00:00

[    2.460000] TI DaVinci EMAC Linux version updated 4.0

[    2.470000] Linux video capture interface: v2.00

[    2.470000] vpfe_init

[    2.470000] starting ccdc_reset...<7>

[    2.480000] End of ccdc_reset...<5>vpfe_probe

[    2.490000] vpfe ccdc capture vpfe ccdc capture.1: vpif_register_decoder: decoder = MT9P031

[    2.500000] Trying to register davinci display video device.

[    2.500000] layer=c516be00,layer->video_dev=c516bf60

[    2.510000] Trying to register davinci display video device.

[    2.510000] layer=c516bc00,layer->video_dev=c516bd60

[    2.520000] davinci_init:DaVinci V4L2 Display Driver V1.0 loaded

[    2.530000] i2c /dev entries driver

[    2.530000] nand_davinci nand_davinci.0: Using 4-bit hardware ECC

[    2.540000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)

[    2.550000] 2 NAND chips detected

[    2.560000] 4 cmdlinepart partitions found on MTD device nand_davinci.0

[    2.570000] Creating 4 MTD partitions on "nand_davinci.0":

[    2.570000] 0x00000000-0x003e0000 : "UBOOT"

[    2.580000] 0x003e0000-0x00400000 : "UBOOT_ENV"

[    2.580000] 0x00400000-0x00720000 : "KERNEL"

[    2.590000] 0x00720000-0x0cf20000 : "FS"

[    2.600000] nand_davinci nand_davinci.0: hardware revision: 2.3

[    2.610000] dm_spi.0: davinci SPI Controller driver at 0xc5816000 (irq = 42) use_dma=0

[    2.620000] Initializing USB Mass Storage driver...

[    2.620000] usbcore: registered new driver usb-storage

[    2.630000] USB Mass Storage support registered.

[    2.630000] musb_hdrc: version 6.0, pio, host, debug=0

[    2.640000] MUX: initialized GPIO33

[    2.660000] musb_hdrc: USB Host mode controller at c581e000 using PIO, IRQ 12

[    2.660000] musb_hdrc musb_hdrc: MUSB HDRC host driver

[    2.670000] musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1

[    2.680000] usb usb1: configuration #1 chosen from 1 choice

[    2.680000] hub 1-0:1.0: USB hub found

[    2.690000] hub 1-0:1.0: 1 port detected

[    2.800000] davinci-mmc davinci-mmc.0: Supporting 4-bit mode

[    2.800000] davinci-mmc davinci-mmc.0: Using DMA mode

[    2.810000] Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).

[    2.820000] ASoC version 0.13.1

[    2.830000] AIC3X Audio Codec 0.2

[    2.840000] asoc: aic3x <-> davinci-i2s mapping ok

[    2.920000] ALSA device list:

[    2.930000]   #0: DaVinci DM365 EVM (aic3x)

[    2.930000] TCP bic registered

[    2.930000] NET: Registered protocol family 1

[    2.940000] NET: Registered protocol family 17

[    2.940000] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)

[    2.950000] Time: timer0_1 clocksource has been installed.

[    2.960000] Clock event device timer0_0 configured with caps set: 08

[    2.960000] Switched to high resolution mode on CPU 0

[    4.480000] Sending DHCP requests .., OK

[    7.260000] IP-Config: Got DHCP answer from 192.168.1.1, my address is 192.168.1.27

[    7.260000] IP-Config: Complete:

[    7.260000]       device=eth0, addr=192.168.1.27, mask=255.255.255.0, gw=192.168.1.1,

[    7.270000]      host=192.168.1.27, domain=, nis-domain=(none),

[    7.280000]      bootserver=192.168.1.1, rootserver=192.168.1.72, rootpath=

[    7.280000] Looking up port of RPC 100003/2 on 192.168.1.72

[    7.310000] Looking up port of RPC 100005/1 on 192.168.1.72

[    7.320000] Root-NFS: Server returned error -13 while mounting /home/stephane/DM365SDK844703/fs/fs

[    7.330000] VFS: Unable to mount root fs via NFS, trying floppy.

[    7.340000] VFS: Cannot open root device "nfs" or unknown-block(2,0)

[    7.340000] Please append a correct "root=" boot option

[    7.340000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

[    7.360000] [<c0039b94>] (dump_stack+0x0/0x14) from [<c004871c>] (panic+0x4c/0x130)

[    7.360000] [<c00486d0>] (panic+0x0/0x130) from [<c0008d80>] (mount_block_root+0x1c4/0x208)

[    7.370000]  r3 = C02702E8  r2 = 00000000  r1 = C03E1F18  r0 = C021F0A8

[    7.370000] [<c0008bbc>] (mount_block_root+0x0/0x208) from [<c0008e88>] (mount_root+0xc4/0xfc)

[    7.380000] [<c0008dc4>] (mount_root+0x0/0xfc) from [<c0008fa8>] (prepare_namespace+0xe8/0x140)

[    7.390000]  r5 = C00326E4  r4 = C02D175C

[    7.400000] [<c0008ec0>] (prepare_namespace+0x0/0x140) from [<c00351a0>] (init+0x174/0x27c)

[    7.400000]  r5 = C0032180  r4 = C02D174C

[    7.410000] [<c003502c>] (init+0x0/0x27c) from [<c004b7a0>] (do_exit+0x0/0x854)

what I have to do?

I'm fed up to have so many mistakes!!

It is time you give back to the community.  Instead of complaining what you don't like, fix it.

Pascal is creating easy to follow  step-by-step instructions for people who are not familiar with the technologies commonly used for embedded Linux development.  Please see if Pascal is interested in help with his contribution back to the community.

Todd

Any idea for my problem?

Yes.

Look for the word "error" in the output that isn't working right.  In your case

Root-NFS: Server returned error -13 while mounting /home/stephane/DM365SDK844703/fs/fs

Search the internet for some of that text, like Root-NFS: Server returned error -13 while mounting

Is the IP address of your NFS server 192.168.1.72?

Have you verified your NFS server is configured properly?

www.ridgerun.com/.../Setting_Up_A_NFS_Service

processors.wiki.ti.com/.../Linux_Host_Configuration_-_Ubuntu

Also, run wireshark on your nfs server machine - that lets you see the network packets being exchanged which is helpful in figure out which side is misconfigured.

Todd

I have verified that my NFS server is configured properly and the address IP of my PC is: 192.168.1.72

The LeopardBoard is connected to a PoE Switch

I don't know how to use wireshark, I have tried but I could see in the console: dumpcap: There are no interfaces on which a capture can be done

I succeed in making a capture with wireshark. I have done it when I have run "boot" (in the u-boot prompt)

Here is the result:

thank you in advance

Aurélie

 

Aurélie,

You say you verified your NFS server configuration, but wireshark is showing a permission denied error (ERR_ACCESS, which I think is permission denied, I can't see the exact status byte in the packet cracker window).

If you have a second PC that can do an NFS mount of your NFS server's $DEVDIR/fs/fs directory, that would show for sure you have NFS server configured properly.

Todd

Oh stupid mistake: I wrote  #/home/ * (rw,insecure,no_root_squash,no_subtree_check)

whereas /home/*(rw,insecure,no_root_squash,no_subtree_check)     (I kept the #)

So sorry

hi sir ,

i am also getting similar type errors while running uboot on leo dm 365, following is what i am getting when performing boot

U-Boot 1.3.4-svn76 (May  5 2011 - 11:54:32)

I2C:   ready

DRAM:  128 MB

NAND:  NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)

Bad block table found at page 131008, version 0x01

Bad block table found at page 130944, version 0x01

256 MiB

In:    serial

Out:   serial

Err:   serial

Ethernet PHY: GENERIC @ 0x00

Hit any key to stop autoboot:  0

Loading from NAND 256MiB 3,3V 8-bit, offset 0x400000

  Image Name:   "RR Linux Kernel"

  Image Type:   ARM Linux Kernel Image (uncompressed)

  Data Size:    4427904 Bytes =  4.2 MB

  Load Address: 80008000

  Entry Point:  80008000

Automatic boot of image at addr 0x82000000 ...

## Booting kernel from Legacy Image at 82000000 ...

  Image Name:   "RR Linux Kernel"

  Image Type:   ARM Linux Kernel Image (uncompressed)

  Data Size:    4427904 Bytes =  4.2 MB

  Load Address: 80008000

  Entry Point:  80008000

  Verifying Checksum ... OK

  Loading Kernel Image ... OK

OK

Starting kernel ...

Linux version 2.6.32-rc2-ridgerun (root@11CPU0048L) (gcc version 4.2.4) #24 PREEMPT Fri May 6 14:31:28 IST 2011

CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177

CPU: VIVT data cache, VIVT instruction cache

Machine: DM365 Leopard

Memory policy: ECC disabled, Data cache writeback

DaVinci dm365_rev1.2 variant 0x8

Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 13716

Kernel command line: davinci_enc_mngr.ch0_output=COMPONENT davinci_enc_mngr.ch0_mode=720P-60 davinci_display.cont2_bufsize=6291456 vpfe_capture.cont_bufoffset=6291456 vpfe_capture.cont_bufsize=6291456 console=ttyS0,115200n8 video=davincifb:vid0=off:vid1=off:osd1=off dm365_imp.oper_mode=0 davinci_capture.device_type=4 vpfe_capture.interface=1 mem=54M root=/dev/nfs nfsroot=:/root/work/leo365/fs/fs rw ip=dhcp mtdparts=nand_davinci.0:3968k(UBOOT),128k(UBOOT_ENV),4352k(KERNEL),204800k(FS)

Unknown boot option `davinci_capture.device_type=4': ignoring

PID hash table entries: 256 (order: -2, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Memory: 54MB = 54MB total

Memory: 50124KB available (3980K code, 385K data, 148K init, 0K highmem)

SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

Hierarchical RCU implementation.

NR_IRQS:245

Console: colour dummy device 80x30

Calibrating delay loop... 147.86 BogoMIPS (lpj=739328)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

DaVinci: 8 gpio irqs

NET: Registered protocol family 16

davinci_serial_init:97: failed to get UART2 clock

bio: create slab <bio-0> at 0

DM365 IPIPE initialized in Continuous mode

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

vpss vpss: dm365_vpss vpss probed

vpss vpss: dm365_vpss vpss probe success

dm365_afew_hw_init

ch0 default output "COMPONENT", mode "720P-60"

VPBE Encoder Initialized

cfg80211: Using static regulatory domain info

cfg80211: Regulatory domain: US

(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)

(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)

(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)

(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)

cfg80211: Calling CRDA for country: US

LogicPD encoder initialized

Leopard DVI encoder initialized

Switching to clocksource timer0_1

musb_hdrc: version 6.0, cppi-dma, host, debug=0

musb_hdrc: USB Host mode controller at fec64000 using DMA, IRQ 12

musb_hdrc musb_hdrc: MUSB HDRC host driver

musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NET: Registered protocol family 1

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

RPC: Registered tcp NFSv4.1 backchannel transport module.

JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.

msgmni has been set to 98

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler anticipatory registered (default)

davincifb davincifb.0: dm_osd0_fb: 1280x720x16@0,0 with framebuffer size 1800KB

davincifb davincifb.0: dm_osd1_fb: 1280x720x4@0,0 with framebuffer size 1800KB

DM365 IPIPEIF probed

imp serializer initialized

davinci_previewer initialized

davinci_resizer initialized

Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A

console [ttyS0] enabled

brd: module loaded

console [netcon0] enabled

netconsole: network logging started

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

usbcore: registered new interface driver usbtest

i2c /dev entries driver

Linux video capture interface: v2.00

ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter)

vpfe_init

vpfe-capture: vpss clock vpss_master enabled

vpfe-capture vpfe-capture: v4l2 device registered

vpfe-capture vpfe-capture: video device registered

Leopard: switch to HD imager-MT9P031 video input

mt9p031 1-0048: Detected a MT9P031 chip ID 1801

mt9p031 1-0048: mt9p031 1-0048 decoder driver registered !!

vpfe-capture vpfe-capture: v4l2 sub device mt9p031 registered

vpfe_register_ccdc_device: DM365 ISIF

DM365 ISIF is registered with vpfe.

af major#: 252, minor# 0

AF Driver initialized

aew major#: 251, minor# 0

AEW Driver initialized

Trying to register davinci display video device.

layer=c25f0800,layer->video_dev=c25f0970

Trying to register davinci display video device.

layer=c25f0c00,layer->video_dev=c25f0d70

davinci_init:DaVinci V4L2 Display Driver V1.0 loaded

watchdog watchdog: heartbeat 60 sec

davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode

usbcore: registered new interface driver usbhid

usbhid: v2.6:USB HID core driver

Advanced Linux Sound Architecture Driver Version 1.0.21.

No device for DAI tlv320aic3x

No device for DAI davinci-i2s

asoc: tlv320aic3x <-> davinci-i2s mapping ok

ALSA device list:

 #0: DaVinci EVM (tlv320aic3x)

TCP cubic registered

NET: Registered protocol family 17

lib80211: common routines for IEEE802.11 drivers

Clocks: disable unused mmcsd1

Clocks: disable unused spi0

Clocks: disable unused spi1

Clocks: disable unused spi2

Clocks: disable unused spi3

Clocks: disable unused spi4

Clocks: disable unused aemif

Clocks: disable unused pwm0

Clocks: disable unused pwm1

Clocks: disable unused pwm2

Clocks: disable unused pwm3

Clocks: disable unused timer1

Clocks: disable unused timer3

Clocks: disable unused emac

Clocks: disable unused voice_codec

Clocks: disable unused rto

Clocks: disable unused mjcp

davinci_emac_probe: using random MAC addr: c2:5b:a5:ee:ef:92

emac-mii: probed

Sending DHCP requests ......, OK

IP-Config: Got DHCP answer from 0.0.0.0, my address is 192.168.215.81

IP-Config: Complete:

    device=eth0, addr=192.168.215.81, mask=255.255.255.0, gw=192.168.215.254,

    host=192.168.215.81, domain=amritavidya.edu, nis-domain=(none),

    bootserver=0.0.0.0, rootserver=0.0.0.0, rootpath=

Looking up port of RPC 100003/2 on 0.0.0.0

rpcbind: server 0.0.0.0 not responding, timed out

Root-NFS: Unable to get nfsd port number from server, using default

Looking up port of RPC 100005/1 on 0.0.0.0

rpcbind: server 0.0.0.0 not responding, timed out

Root-NFS: Unable to get mountd port number from server, using default

Root-NFS: Server returned error -5 while mounting /tftpboot/:/root/work/leo365/fs/fs

VFS: Unable to mount root fs via NFS, trying floppy.

VFS: Cannot open root device "nfs" or unknown-block(2,0)

Please append a correct "root=" boot option; here are the available partitions:

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

Backtrace:

[<c0031700>] (dump_backtrace+0x0/0x110) from [<c0031844>] (dump_stack+0x18/0x1c)

r6:c0026850 r5:c04417e4 r4:c2029f58

[<c003182c>] (dump_stack+0x0/0x1c) from [<c004246c>] (panic+0x54/0x134)

[<c0042418>] (panic+0x0/0x134) from [<c0008fec>] (mount_block_root+0x1d4/0x21c)

r3:00000001 r2:c2028000 r1:c2029f58 r0:c03a6154

[<c0008e18>] (mount_block_root+0x0/0x21c) from [<c00090f8>] (mount_root+0xc4/0xfc)

[<c0009034>] (mount_root+0x0/0xfc) from [<c000929c>] (prepare_namespace+0x16c/0x1d0)

r5:c0026808 r4:c04412b8

[<c0009130>] (prepare_namespace+0x0/0x1d0) from [<c00087d8>] (kernel_init+0xdc/0x110)

r5:c0024fb0 r4:c0441098

[<c00086fc>] (kernel_init+0x0/0x110) from [<c004568c>] (do_exit+0x0/0x654)

r5:00000000 r4:00000000

please help me to resolve this issue...how to configure boot server and root server?

somebody please help

warm regards

Arjun

Your kernel command line nfsroot

Kernel command line: davinci_enc_mngr.ch0_output=COMPONENT davinci_enc_mngr.ch0_mode=720P-60 davinci_display.cont2_bufsize=6291456 vpfe_capture.cont_bufoffset=6291456 vpfe_capture.cont_bufsize=6291456 console=ttyS0,115200n8 video=davincifb:vid0=off:vid1=off:osd1=off dm365_imp.oper_mode=0 davinci_capture.device_type=4 vpfe_capture.interface=1 mem=54MKernel command line: davinci_enc_mngr.ch0_output=COMPONENT davinci_enc_mngr.ch0_mode=720P-60 davinci_display.cont2_bufsize=6291456 vpfe_capture.cont_bufoffset=6291456 vpfe_capture.cont_bufsize=6291456 console=ttyS0,115200n8 video=davincifb:vid0=off:vid1=off:osd1=off dm365_imp.oper_mode=0 davinci_capture.device_type=4 vpfe_capture.interface=1 mem=54M root=/dev/nfs nfsroot=:/root/work/leo365/fs/fs rw ip=dhcp mtdparts=nand_davinci.0:3968k(UBOOT),128k(UBOOT_ENV),4352k(KERNEL),204800k(FS) root=/dev/nfs nfsroot=:/root/work/leo365/fs/fs rw ip=dhcp mtdparts=nand_davinci.0:3968k(UBOOT),128k(UBOOT_ENV),4352k(KERNEL),204800k(FS)

You have

nfsroot=:/root/work/leo365/fs/fs

Working boot output can be found at

www.ridgerun.com/.../LoepardBoard_365_Evaluation_SDK_Example_Boot_Output

hi sir,

how can i configure boot server and root server? i saw the output but i am still confused. how to configure those addresses? does it require another computer for configuring all these ips? 

please help

warm regards

Arjun

hi sir,

 

I am facing an issue when booting the leopard board. The issue is, i have selected serial port for both communication method and binary uploading, but still it requires nfs server configured!

2. i am assigning static ip address while configuring the sdk but still it is sending dhcp request while booting the target hardware! 

will u please clarify these issue?

You must post output showing the problem if you want detailed help.

Run

make config

in the file system menu, make sure you don't have root NFS selected.

Todd