Hi all,

I want to use the LI-VI365 with the LB. I have got populated R196 and R197.

I follow this step : https://www.ridgerun.com/developer/wiki/index.php/Hardware_setup_-_LeopardBoard_DM365#Video_composite_input_board_-_LI-VI365

This is my bootlog:


U-Boot 2010.12-rc2 (Apr 13 2012 - 11:14:33)

Cores: ARM 297 MHz
DDR:   243 MHz
I2C:   ready
DRAM:  128 MiB
NAND:  256 MiB
MMC:   davinci: 0, davinci: 1
Net:   Ethernet PHY: GENERIC @ 0x00
DaVinci-EMAC
Hit any key to stop autoboot:  0

Loading from nand0, offset 0x400000
   Image Name:   "RR Linux Kernel"
   Created:      2012-04-13  13:47:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4269216 Bytes = 4.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
Automatic boot of image at addr 0x82000000 ...
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   "RR Linux Kernel"
   Created:      2012-04-13  13:47:50 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    4269216 Bytes = 4.1 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK

Starting kernel ...

Linux version 2.6.32-17-ridgerun (stephane@Tamara) (gcc version 4.3.3 (Sourcery G++ Lite 2009q1-203) ) #4 PREEMPT Fri Apr 13 15:47:17 CEST 2012
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: DM365 Leopard
Memory policy: ECC disabled, Data cache writeback
DaVinci dm36x_rev1.2 variant 0x8
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 25146
Kernel command line: davinci_enc_mngr.ch0_output=COMPOSITE davinci_enc_mngr.ch0_mode=NTSC davinci_display.cont2_bufsize=3145728 vpfe_capture.cont_bufoffset=3145728 vpfe_capture)
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 99MB = 99MB total
Memory: 95928KB available (3840K code, 287K data, 140K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:245
Console: colour dummy device 80x30
Calibrating delay loop... 147.86 BogoMIPS (lpj=739328)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
DaVinci: 8 gpio irqs
NET: Registered protocol family 16
davinci_serial_init:97: failed to get UART2 clock
bio: create slab <bio-0> at 0
DM365 IPIPE initialized in Continuous mode
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
vpss vpss: dm365_vpss vpss probed
vpss vpss: dm365_vpss vpss probe success
dm365_afew_hw_init
ch0 default output "COMPOSITE", mode "NTSC"
VPBE Encoder Initialized
LogicPD encoder initialized
Switching to clocksource timer0_1
musb_hdrc: version 6.0, cppi-dma, host, debug=0
musb_hdrc: USB Host mode controller at fec64000 using DMA, IRQ 12
musb_hdrc musb_hdrc: MUSB HDRC host driver
musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
msgmni has been set to 187
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
davincifb davincifb.0: dm_osd0_fb: 720x480x16@0,0 with framebuffer size 1350KB
davincifb davincifb.0: dm_vid0_fb: 0x0x16@0,0 with framebuffer size 1020KB
davincifb davincifb.0: dm_osd1_fb: 0x0x8@0,0 with framebuffer size 675KB
davincifb davincifb.0: dm_vid1_fb: 0x0x16@0,0 with framebuffer size 1020KB
DM365 IPIPEIF probed
imp serializer initialized
davinci_previewer initialized
davinci_resizer initialized
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0x1c20000 (irq = 40) is a 16550A
console [ttyS0] enabled
brd: module loaded
loop: module loaded
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
Scanning device for bad blocks
3 cmdlinepart partitions found on MTD device davinci_nand.0
Creating 3 MTD partitions on "davinci_nand.0":
0x000000000000-0x000000400000 : "UBOOT"
0x000000400000-0x000000880000 : "KERNEL"
0x000000880000-0x00000d080000 : "FS"
davinci_nand davinci_nand.0: controller rev. 2.3
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbtest
i2c /dev entries driver
Linux video capture interface: v2.00
ths7303 1-002c: chip found @ 0x58 (DaVinci I2C adapter)
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
...
i2c_davinci i2c_davinci.1: timeout waiting for bus ready
i2c_davinci i2c_davinci.1: timeout waiting for bus ready
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
...
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
i2c_davinci i2c_davinci.1: initiating i2c bus recovery
...
i2c_davinci i2c_davinci.1: timeout waiting for bus ready
i2c_davinci i2c_davinci.1: timeout waiting for bus ready
tvp5146: chip id mismatch msb:0x92 lsb:0x92
tvp5146: tvp514x decoder not detected
vpfe-capture vpfe-capture: v4l2 sub device tvp5146 register fails
No sub devices registered
vpfe-capture: vpfe capture clocks disabled
vpfe_register_ccdc_device: DM365 ISIF
dm365_isif: probe of dm365_isif failed with error -22
af major#: 252, minor# 0
AF Driver initialized
aew major#: 251, minor# 0
AEW Driver initialized
Trying to register davinci display video device.
layer=c5352c00,layer->video_dev=c5352d64
Trying to register davinci display video device.
layer=c5353000,layer->video_dev=c5353164
davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
watchdog watchdog: heartbeat 60 sec
davinci_mmc davinci_mmc.0: Using DMA, 4-bit mode
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
Clocks: disable unused mmcsd1
Clocks: disable unused spi0
Clocks: disable unused spi1
Clocks: disable unused spi2
Clocks: disable unused spi3
Clocks: disable unused spi4
Clocks: disable unused pwm0
Clocks: disable unused pwm1
Clocks: disable unused pwm2
Clocks: disable unused pwm3
Clocks: disable unused timer1
Clocks: disable unused timer3
Clocks: disable unused emac
Clocks: disable unused voice_codec
Clocks: disable unused asp0
Clocks: disable unused rto
Clocks: disable unused mjcp
davinci_emac_probe: using random MAC addr: ee:d3:1d:8e:c3:7e
emac-mii: probed
IP-Config: Complete:
     device=eth0, addr=192.168.1.120, mask=255.255.255.0, gw=255.255.255.255,
     host=192.168.1.120, domain=, nis-domain=(none),
     bootserver=255.255.255.255, rootserver=192.168.1.72, rootpath=
Looking up port of RPC 100003/2 on 192.168.1.72
Looking up port of RPC 100005/1 on 192.168.1.72
VFS: Mounted root (nfs filesystem) on device 0:13.
Freeing init memory: 140K
init started: BusyBox v1.18.2 (2012-04-13 10:34:30 CEST)
starting pid 981, tty '': '/etc/rcS'
Starting System
done.
Welcome to
__________ .__     .___               __________                
\______   \|__|  __| _/  ____    ____ \______   \ __ __   ____  
 |       _/|  | / __ |  / ___\ _/ __ \ |       _/|  |  \ /    \
 |    |   \|  |/ /_/ | / /_/  >\  ___/ |    |   \|  |  /|   |  \
 |____|_  /|__|\____ | \___  /  \___  >|____|_  /|____/ |___|  /
        \/          \//_____/       \/        \/             \/
           
    Embedded Linux Solutions

Does anyone arrived to use LI-VI365 with LB365?

What's my problem? any issue ?

Thanks for all

Regards

Maxime Suire